Signal Sources
Instrument that provides a stimulus signal (waveform). (www.tek.com)
See Also: Signal, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signaling, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners
-
product
Function Generators
Respective dual channels function/arbitrary waveform generator. Sine wave output up to 160MHz, full-band resolution of 1μHz. Pulse waveform up to 50MHz (or 40MHz), adjustable time of rising, falling and duty ratio. Sampling rate of 500MSa/s and vertical resolution of 16bit. 6-bit high-precision frequency meter compatible with TTL level signal. Arbitrary wave storage of 8~32M points, 7GB non-volatile waveform storage. Multi modulation function::AM,FM,PM, ASK,FSK,PSK, BPSK, QPSK,OSK,PWM, QAM, SUM ...show more -
product
16-Bit Digitizer
PA72D16180A
The PA72D16180A is a 16-bit digitizer, capable of capturing waveforms at speeds up to 180Msps. An onboard offset voltage source allows capturing offset signals while still using the optimal range for maximum ADC utilization. Two onboard filters allow suppression of out-of-band noise. The 64MWord onboard memory enables capturing very long waveforms, or sequentially capturing multiple signals with minimal intermediate bus communication.
-
product
16-Channel RTD Signal Conditioning Card
ProDAQ 5821
The ProDAQ 5821 series of Signal Conditioning Cards is designed to interface with a variety of sensors, principally RTDs, Thermistors, Cryogenic Diodes and Voltage type sensors. Each version of the 5821 provides the capability of precise 4-wire measurement. In order to achieve this, a precise 500μA constant current source is provided per channel. The current source can be disabled on a per channel basis and is monitored to ensure that current is flowing. The value of the output current is stored...show more -
product
Video Signal Distributor
MSHM-305A/310A
MSHM-305A/310A, HDMI Distribution,Amplifier, distribute three digital video input sources to the five (or ten) output channels. The built in amplification function enables HDMI signal distribution without signal loss. The product guarantees to support full channels HDMI/HDCP compliance. User can select one input source of the three and make sure connected condition with led of the front panel.
-
product
INFRATEST Software
INFRATEST is a powerful software for testing visible to IR cameras, goggles and laser rangefinders. Based on video acquisition modules compatible with a wide range of communication protocols, INFRATEST acquires, displays and analyzes the video signal from all types of electro-optical devices. In addition, INFRATEST manages the optical stimuli delivered to the camera through the control of blackbodies and visible/NIR optical sources and their accessories (collimator, target wheel, harmonization modules, etc.).
-
product
Single Channel High Voltage Linear Amplifier
A600
The A600 is a general purpose broadband linear amplifier having a fixed amplification of 100 times and capable of bipolar high voltage output of 300V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to 3 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
product
RF And Microwave Signal Generation And Analysis
The need for microwave test and measurement technology is even more urgent than the need for microwave equipment itself. Therefore, Shengbo Technology is relying on its own research and development capabilities to strive to become one of the comprehensive microwave test and measurement equipment suppliers. We provide a wide range of RF microwave test products, including a good-quality full-band broadband up-down converter . You can provide 2GHz real-time bandwidth signal up-down conversion funct...show more -
product
Telecom Test Systems
4301 Series
The 4301 is designed to work with a standard arbitrary wave form generator or signal source that can be triggered. The system can be ordered with an optional Fluke 281 arbitrary waveform generator, which comes pre-programmed and integrated into the 4301 system. When equipped with the Fluke 281 option, the 4301 provides a complete solution for GR-1089 Section 10/ATIS-0600315.2007 testing.
-
product
Low-Cost HDMI Extender
ST-C6HD-150-LC
The XTENDEX® Low-Cost HDMI Extender transmits digital video and audio signals up to 150 feet using one CAT5e/6 cable. Each video extender consists of a local unit that connects to an HDMI source and a remote unit that connects to an HDMI display.
-
product
Precision Programmable AC and DC Sources, 0 - 333VAC, 0 - 3,000A / Phase, 15kVA - 1.08MVA
Tahoe Series
AMETEK Programmable Power, Inc.
The California Instruments Tahoe Series combines intelligence and flexibility with high power to create an advanced platform of AC solutions. Using a state-of-the art SiC power switching architecture and Digital Signal Processing, the Tahoe Series combines a robust, high-power AC/DC source with an advanced power analyzer in a single floor standing chassis.
-
product
Video Signal Distributor
MSDS-4416
MSDS-4416 distribute four TMDS input signal up to four display devices such as Projector, PDP, HDTV and TFT-LCD without diminution and distortion. The distribution support single/dual 8~16 bit and user can select input signal by press button and make sure being connected input source with led of the front panel.
-
product
Light Sources
Fiber optic light sources are a low-cost way to analyze and identify accurate fiber optic readings, while certifying optical fiber. Receive the ability to measure fiber optic light continuity, loss, and quality of the signal.
-
product
Frequency Converter
FC5-29M
Frequency converter FC5-29M is a measurement instrument which is designed for spectrum conversion of 75 - 170 GHz to 1 MHz ÷ 2,6 GHz range and automatic frequency measurement of sinusoidal signals. When combined with the 1 MHz - 3,0 GHz spectrum analyzer, FC5-29M can be used for examination of the continuous and periodically repeating pulse signals.The instrument is meant to be used for measurement of various signal sources, radio-transmitting instruments, synthesizers, frequency converters, measurement generators and also for adjustment and verification of various radio-transmitting or communication instruments in laboratory and workshop conditions.
-
product
Multifunction Calibrators
These field and bench calibrators source, simulate, and measure pressure, temperature, and electrical signals with exceptional precision. They can automate calibration procedures, store data, and even calibrate and troubleshoot HART-compatible devices. Our bench calibrator can even be used to calibrate our field calibrators. Also find here 5.5- and 6.5-digit bench multimeters for to assist with a variety of general test and calibration applications.
-
product
GPIB Parallel Interface
Model 4813
* Provides 128 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Optional Relay Driver boards add 64 or 128 Relay Drivers.
-
product
Video Signal Distributor
MSHM-305A Plus
MSHM-305A Plus, HDMI Distribution Amplifier, distributes three digital video input sources to the five output channels. The built-in amplification function enabled HDMI signal distribution without signal loss. The product guarantees to support full channels HDMI/HDCP compliance. It is also built-in CEC function according to current market request. User can select one (1) input source of the three and make sure connected condition with led of the front panel.
-
product
High Power RF-Signal Generators
Becker Nachrichtentechnik GmbH
Multi channel RF signal sources with precise high power output levels. Each output offers a separate, analogue level control. This ensures highest precision in level during a long term usage.
-
product
Quadrature Signal Generator
TE5100-PCI
The TE5100 is a 100MHz Direct Digital Synthesized Signal Generator available in a 3U, CompactPCI or straight PCI format. The TE5100 generates Sine and ACMOS/TTL output signals simultaneously up to 100MHz in 1 µHz steps. Sweep, FSK, Chirp and Single Tone are generated on board. The virtual panel allows control up to 100MHz of all parameters. The TE5100 is equipped with a ±1ppm on-board TCXO clock and can accept an external clock source.
-
product
Zero Bias Schottky Detectors
Fairview Microwave’s line of coaxial packaged zero bias Schottky detectors feature matched inputs for excellent VSWR, voltage sensitivity levels that range from 100 to 500 mV/mW for small signal detection, negative video output polarity, and can withstand maximum input power levels up to +20 dBm CW. Operating temperature range covers 0°C to +90°C and storage temperature of -65°C to +125°C. These zero bias Schottky detectors utilize compact cylindrical package outlines that are made of passivated...show more -
product
Keysight Dual 1x2 SPDT Terminated Microwave Switch Module for 34980A
34946A
The Keysight 34946A microwave switch for the 34980A Multifunction Switch/Measure Unit offers bi-directional switching for test signals from DC to 26.5 GHz. These switches provide excellent insertion loss, isolation, and VSWR specification. The microwave switches are configured as two independent 1x2 (SPDT) terminated switches on a single module. For general-purpose microwave switching applications, the module can be used to switch separate signal sources for a multi-band receiver/transmitter testing application.
-
product
PXI Signal Generators (Signal Sources)
Accelerate test throughput with fast, high-quality measurements optimized for RF or microwave design validation & manufacturing testIncrease test configuration flexibility with a PXI platform and license key upgradesReduce development time with easy integration of drivers and programming examples into test environments
-
product
GPS NTP Time Server - SYNTIME
Signals & Systems India Private Limited
Your product description goes hGPS NTP Time Server (SYNTIME) for Network Time Synchronization is a highly accurate time server. It generates time protocols to synchronize NTP/SNTP clients (Simple Network Time Protocol)/PTP clients (Precision time protocol IEEE 1588) over the network and operates at a speed of 10/100/1000Mbps. The NTP server accepts the time and frequency signals from sources like GPS or GLONASS. It achieves nanosecond accuracy and the system clock operates at stratum 1 when sync...show more -
product
PXI-2797, 40 GHz, 50 Ω, 6x1 (SP6T) Terminated PXI RF Multiplexer Switch Module
782357-01
40 GHz, 50 Ω, 6x1 (SP6T) Terminated PXI RF Multiplexer Switch Module—The PXI‑2797 offers a high-density, terminated multiplexer with dual 6x1 multiplexer banks in the same module. The internal termination of the PXI‑2797 helps prevent high-power reflections that arise from open channels on the module. It is ideal for passing high-order harmonics from PXI RF Signal Upconverter modules or routing multiple sources to PXI RF Signal Downconverter modules.
-
product
Process Controllers
Orbit Controls process controllers are designed for direct connection to virtually all industrial sensors and signal sources. They can be used as process monitors to display the process variables to be measured or as process controllers to monitor processes. In addition to the digital display, the devices also have data interfaces, analog outputs and set point outputs. Simple process monitors are optimized in the factory for the desired measuring range and function at the customer's request. The programmable controllers can be parameterized on site via the keyboard or the data interface.
-
product
Speaker Component Checker
Cab Driver
Whirlwind Music Distributors, Inc.
The CAB DRIVER is a test device for checking the operation of the speaker components within enclosures. A pink noise signal source is sent through pushbutton selectors to an assortment of speaker connectors, including Speakon NL8 and NL4, 1/4" TS and banana jacks. Speaker/ Polarity/ Impedance/ Pink Noise Generator
-
product
PXI-2515, 35-Channel, 0.25 A PXI Signal Insertion Switch Module
778572-15
35-Channel, 0.25 A PXI Signal Insertion Switch Module—The PXI‑2515 is a multiplexer switch module that enables connectivity by routing high-speed digital I/O (DIO) signals between a device under test (DUT) and an NI high-speed DIO device or a parametric measurement device. You can use modules such as PXI Source Measure Units (SMUs) and PXI Digital Multimeters (DMMs) with high-speed digital devices. With the PXI‑2515, you can perform parametric tests on digital pins without external connectivity or impedance mismatch challenges.
-
product
Digital, Hand-Held, Battery Operated Meter
CM-2
The Camera Master II is a digital, hand-held, battery operated meter that measures six different characteristics of any video signal. Use it for fast and accurate set-up of any video source.
-
product
PXI-2545, 2.7 GHz, 50 Ω, Terminated 4x1 PXI RF Multiplexer Switch Module
778572-45
2.7 GHz, 50 Ω, Terminated 4x1 PXI RF Multiplexer Switch Module—The PXI‑2545 is an RF signal multiplexer switch module. The internal termination of the PXI‑2545, which helps prevent high-power reflections that arise from open channels on the module, makes it ideal for use in RF applications where such reflections can damage the source. The module also provides excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use the onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
product
RF Reference Sources
The 27 GHz 96270A and 4 GHz 96040A Low Phase Noise Reference Sources are designed specifically for RF calibration, featuring a calibration-oriented interface, precision signal level and attenuation, high signal purity and precision low distortion modulation. Both instruments simplify the process of RF calibration by reducing the amount of equipment and simplifying the calculations required.
-
product
IEPE Signal Conditioning Amplifiers
Although IEPE (Integrated Electronics Piezoelectric) sensors is not a new technology there are a wide variety of applications where the measurement instrumentation is not configured with IEPE signal conditioning built in. In these situations it is necessary for the IEPE supply to be provided by an external source. Usually this type of instrument will also provide th user with the option to add gain to the signal being conditioned. The Kemo range of IEPE signal conditioning instruments can be used as stand alone conditioners/amplifiers are many of them can also be integrated with filters.
